From 84adefa331c4159d432d22840663c38f155cd4c1 Mon Sep 17 00:00:00 2001 From: Erlang/OTP Date: Fri, 20 Nov 2009 14:54:40 +0000 Subject: The R13B03 release. --- lib/snmp/test/test-mibs/ENTITY-MIB.mib | 784 +++++++++++++++++++++++++++++++++ 1 file changed, 784 insertions(+) create mode 100644 lib/snmp/test/test-mibs/ENTITY-MIB.mib (limited to 'lib/snmp/test/test-mibs/ENTITY-MIB.mib') diff --git a/lib/snmp/test/test-mibs/ENTITY-MIB.mib b/lib/snmp/test/test-mibs/ENTITY-MIB.mib new file mode 100644 index 0000000000..a70c26ed3a --- /dev/null +++ b/lib/snmp/test/test-mibs/ENTITY-MIB.mib @@ -0,0 +1,784 @@ +ENTITY-MIB DEFINITIONS ::= BEGIN + +IMPORTS + MODULE-IDENTITY, OBJECT-TYPE, + mib-2, NOTIFICATION-TYPE + FROM SNMPv2-SMI + TDomain, TAddress, DisplayString, TEXTUAL-CONVENTION, + AutonomousType, RowPointer, TimeStamp + FROM SNMPv2-TC + MODULE-COMPLIANCE, OBJECT-GROUP + FROM SNMPv2-CONF; + +entityMIB MODULE-IDENTITY + LAST-UPDATED "9605160000Z" + ORGANIZATION "IETF ENTMIB Working Group" + CONTACT-INFO + " WG E-mail: entmib@cisco.com + Subscribe: majordomo@cisco.com + msg body: subscribe entmib + + Keith McCloghrie + ENTMIB Working Group Chair + Cisco Systems Inc. + 170 West Tasman Drive + San Jose, CA 95134 + 408-526-5260 + kzm@cisco.com + + Andy Bierman + ENTMIB Working Group Editor + Cisco Systems Inc. + 170 West Tasman Drive + San Jose, CA 95134 + 408-527-3711 + abierman@cisco.com" + DESCRIPTION + "The MIB module for representing multiple logical + entities supported by a single SNMP agent." + ::= { mib-2 47 } + +entityMIBObjects OBJECT IDENTIFIER ::= { entityMIB 1 } + +-- MIB contains four groups + +entityPhysical OBJECT IDENTIFIER ::= { entityMIBObjects 1 } +entityLogical OBJECT IDENTIFIER ::= { entityMIBObjects 2 } + + +entityMapping OBJECT IDENTIFIER ::= { entityMIBObjects 3 } +entityGeneral OBJECT IDENTIFIER ::= { entityMIBObjects 4 } + + +-- Textual Conventions +PhysicalIndex ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "An arbitrary value which uniquely identifies the physical + entity. The value is a small positive integer; index values + for different physical entities are not necessarily + contiguous." + SYNTAX INTEGER (1..2147483647) + + +PhysicalClass ::= TEXTUAL-CONVENTION + STATUS current + DESCRIPTION + "An enumerated value which provides an indication of the + general hardware type of a particular physical entity." + SYNTAX INTEGER { + other(1), + unknown(2), + chassis(3), + backplane(4), + container(5), -- e.g. slot or daughter-card holder + powerSupply(6), + fan(7), + sensor(8), + module(9), -- e.g. plug-in card or daughter-card + port(10) + } + +-- The Physical Entity Table + +entPhysicalTable OBJECT-TYPE + SYNTAX SEQUENCE OF EntPhysicalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains one row per physical entity. There is + always at least one row for an 'overall' physical entity." + ::= { entityPhysical 1 } + +entPhysicalEntry OBJECT-TYPE + SYNTAX EntPhysicalEntry + MAX-ACCESS not-accessible + STATUS current + + + DESCRIPTION + "Information about a particular physical entity. + + Each entry provides objects (entPhysicalDescr, + entPhysicalVendorType, and entPhysicalClass) to help an NMS + identify and characterize the entry, and objects + (entPhysicalContainedIn and entPhysicalParentRelPos) to help + an NMS relate the particular entry to other entries in this + table." + INDEX { entPhysicalIndex } + ::= { entPhysicalTable 1 } + +EntPhysicalEntry ::= SEQUENCE { + entPhysicalIndex PhysicalIndex, + entPhysicalDescr DisplayString, + entPhysicalVendorType AutonomousType, + entPhysicalContainedIn INTEGER, + entPhysicalClass PhysicalClass, + entPhysicalParentRelPos INTEGER, + entPhysicalName DisplayString +} + +entPhysicalIndex OBJECT-TYPE + SYNTAX PhysicalIndex + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The index for this entry." + ::= { entPhysicalEntry 1 } + +entPhysicalDescr OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A textual description of physical entity. This object + should contain a string which identifies the manufacturer's + name for the physical entity, and should be set to a + distinct value for each version or model of the physical + entity. " + ::= { entPhysicalEntry 2 } + +entPhysicalVendorType OBJECT-TYPE + SYNTAX AutonomousType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An indication of the vendor-specific hardware type of the + + + physical entity. Note that this is different from the + definition of MIB-II's sysObjectID. + + An agent should set this object to a enterprise-specific + registration identifier value indicating the specific + equipment type in detail. The associated instance of + entPhysicalClass is used to indicate the general type of + hardware device. + + If no vendor-specific registration identifier exists for + this physical entity, or the value is unknown by this agent, + then the value { 0 0 } is returned." + ::= { entPhysicalEntry 3 } + +entPhysicalContainedIn OBJECT-TYPE + SYNTAX INTEGER (0..2147483647) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of entPhysicalIndex for the physical entity which + 'contains' this physical entity. A value of zero indicates + this physical entity is not contained in any other physical + entity. Note that the set of 'containment' relationships + define a strict hierarchy; that is, recursion is not + allowed." + ::= { entPhysicalEntry 4 } + +entPhysicalClass OBJECT-TYPE + SYNTAX PhysicalClass + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An indication of the general hardware type of the physical + entity. + + An agent should set this object to the standard enumeration + value which most accurately indicates the general class of + the physical entity, or the primary class if there is more + than one. + + If no appropriate standard registration identifier exists + for this physical entity, then the value 'other(1)' is + returned. If the value is unknown by this agent, then the + value 'unknown(2)' is returned." + ::= { entPhysicalEntry 5 } + +entPhysicalParentRelPos OBJECT-TYPE + SYNTAX INTEGER (-1..2147483647) + + + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An indication of the relative position of this 'child' + component among all its 'sibling' components. Sibling + components are defined as entPhysicalEntries which share the + same instance values of each of the entPhysicalContainedIn + and entPhysicalClass objects. + + An NMS can use this object to identify the relative ordering + for all sibling components of a particular parent + (identified by the entPhysicalContainedIn instance in each + sibling entry). + + This value should match any external labeling of the + physical component if possible. For example, for a module + labeled as 'card #3', entPhysicalParentRelPos should have + the value '3'. + + If the physical position of this component does not match + any external numbering or clearly visible ordering, then + user documentation or other external reference material + should be used to determine the parent-relative position. If + this is not possible, then the the agent should assign a + consistent (but possibly arbitrary) ordering to a given set + of 'sibling' components, perhaps based on internal + representation of the components. + + If the agent cannot determine the parent-relative position + for some reason, or if the associated value of + entPhysicalContainedIn is '0', then the value '-1' is + returned. Otherwise a non-negative integer is returned, + indicating the parent-relative position of this physical + entity. + + Parent-relative ordering normally starts from '1' and + continues to 'N', where 'N' represents the highest + positioned child entity. However, if the physical entities + (e.g. slots) are labeled from a starting position of zero, + then the first sibling should be associated with a + entPhysicalParentRelPos value of '0'. Note that this + ordering may be sparse or dense, depending on agent + implementation. + + The actual values returned are not globally meaningful, as + each 'parent' component may use different numbering + algorithms. The ordering is only meaningful among siblings + of the same parent component. + + + The agent should retain parent-relative position values + across reboots, either through algorithmic assignment or use + of non-volatile storage." + ::= { entPhysicalEntry 6 } + + +entPhysicalName OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The textual name of the physical entity. The value of this + object should be the name of the component as assigned by + the local device and should be suitable for use in commands + entered at the device's `console'. This might be a text + name, such as `console' or a simple component number (e.g. + port or module number), such as `1', depending on the + physical component naming syntax of the device. + + If there is no local name, or this object is otherwise not + applicable, then this object contains a zero-length string. + + Note that the value of entPhysicalName for two physical + entities will be the same in the event that the console + interface does not distinguish between them, e.g., slot-1 + and the card in slot-1." + ::= { entPhysicalEntry 7 } + +-- The Logical Entity Table +entLogicalTable OBJECT-TYPE + SYNTAX SEQUENCE OF EntLogicalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains one row per logical entity. At least + one entry must exist." + ::= { entityLogical 1 } + +entLogicalEntry OBJECT-TYPE + SYNTAX EntLogicalEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about a particular logical entity. Entities + may be managed by this agent or other SNMP agents (possibly) + in the same chassis." + INDEX { entLogicalIndex } + ::= { entLogicalTable 1 } + + +EntLogicalEntry ::= SEQUENCE { + entLogicalIndex INTEGER, + entLogicalDescr DisplayString, + entLogicalType AutonomousType, + entLogicalCommunity OCTET STRING, + entLogicalTAddress TAddress, + entLogicalTDomain TDomain +} + +entLogicalIndex OBJECT-TYPE + SYNTAX INTEGER (1..2147483647) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The value of this object uniquely identifies the logical + entity. The value is a small positive integer; index values + for different logical entities are are not necessarily + contiguous." + ::= { entLogicalEntry 1 } + +entLogicalDescr OBJECT-TYPE + SYNTAX DisplayString + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A textual description of the logical entity. This object + should contain a string which identifies the manufacturer's + name for the logical entity, and should be set to a distinct + value for each version of the logical entity. " + ::= { entLogicalEntry 2 } + +entLogicalType OBJECT-TYPE + SYNTAX AutonomousType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An indication of the type of logical entity. This will + typically be the OBJECT IDENTIFIER name of the node in the + SMI's naming hierarchy which represents the major MIB + module, or the majority of the MIB modules, supported by the + logical entity. For example: + a logical entity of a regular host/router -> mib-2 + a logical entity of a 802.1d bridge -> dot1dBridge + a logical entity of a 802.3 repeater -> snmpDot3RptrMgmt + If an appropriate node in the SMI's naming hierarchy cannot + be identified, the value 'mib-2' should be used." + ::= { entLogicalEntry 3 } + + + +entLogicalCommunity OBJECT-TYPE + SYNTAX OCTET STRING (SIZE (1..255)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An SNMPv1 or SNMPv2C community-string which can be used to + access detailed management information for this logical + entity. The agent should allow read access with this + community string (to an appropriate subset of all managed + objects) and may also choose to return a community string + based on the privileges of the request used to read this + object. Note that an agent may choose to return a community + string with read-only privileges, even if this object is + accessed with a read-write community string. However, the + agent must take care not to return a community string which + allows more privileges than the community string used to + access this object. + + A compliant SNMP agent may wish to conserve naming scopes by + representing multiple logical entities in a single 'main' + naming scope. This is possible when the logical entities + represented by the same value of entLogicalCommunity have no + object instances in common. For example, 'bridge1' and + 'repeater1' may be part of the main naming scope, but at + least one additional community string is needed to represent + 'bridge2' and 'repeater2'. + + Logical entities 'bridge1' and 'repeater1' would be + represented by sysOREntries associated with the 'main' + naming scope. + + For agents not accessible via SNMPv1 or SNMPv2C, the value + of this object is the empty-string." + ::= { entLogicalEntry 4 } + +entLogicalTAddress OBJECT-TYPE + SYNTAX TAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The transport service address by which the logical entity + receives network management traffic, formatted according to + the corresponding value of entLogicalTDomain. + + For snmpUDPDomain, a TAddress is 6 octets long, the initial + 4 octets containing the IP-address in network-byte order and + the last 2 containing the UDP port in network-byte order. + Consult 'Transport Mappings for Version 2 of the Simple + + + Network Management Protocol' (RFC 1906 [8]) for further + information on snmpUDPDomain." + ::= { entLogicalEntry 5 } + +entLogicalTDomain OBJECT-TYPE + SYNTAX TDomain + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the kind of transport service by which the + logical entity receives network management traffic. + Possible values for this object are presently found in the + Transport Mappings for SNMPv2 document (RFC 1906 [8])." + ::= { entLogicalEntry 6 } + +entLPMappingTable OBJECT-TYPE + SYNTAX SEQUENCE OF EntLPMappingEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains zero or more rows of logical entity to + physical equipment associations. For each logical entity + known by this agent, there are zero or more mappings to the + physical resources which are used to realize that logical + entity. + + An agent should limit the number and nature of entries in + this table such that only meaningful and non-redundant + information is returned. For example, in a system which + contains a single power supply, mappings between logical + entities and the power supply are not useful and should not + be included. + + Also, only the most appropriate physical component which is + closest to the root of a particular containment tree should + be identified in an entLPMapping entry. + + For example, suppose a bridge is realized on a particular + module, and all ports on that module are ports on this + bridge. A mapping between the bridge and the module would be + useful, but additional mappings between the bridge and each + of the ports on that module would be redundant (since the + entPhysicalContainedIn hierarchy can provide the same + information). If, on the other hand, more than one bridge + was utilizing ports on this module, then mappings between + each bridge and the ports it used would be appropriate. + + Also, in the case of a single backplane repeater, a mapping + + + for the backplane to the single repeater entity is not + necessary." + ::= { entityMapping 1 } + +entLPMappingEntry OBJECT-TYPE + SYNTAX EntLPMappingEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about a particular logical entity to physical + equipment association. Note that the nature of the + association is not specifically identified in this entry. It + is expected that sufficient information exists in the MIBs + used to manage a particular logical entity to infer how + physical component information is utilized." + INDEX { entLogicalIndex, entLPPhysicalIndex } + ::= { entLPMappingTable 1 } + +EntLPMappingEntry ::= SEQUENCE { + entLPPhysicalIndex PhysicalIndex +} + +entLPPhysicalIndex OBJECT-TYPE + SYNTAX PhysicalIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of this object identifies the index value of a + particular entPhysicalEntry associated with the indicated + entLogicalEntity." + ::= { entLPMappingEntry 1 } + +-- logical entity/component to alias table +entAliasMappingTable OBJECT-TYPE + SYNTAX SEQUENCE OF EntAliasMappingEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains zero or more rows, representing + mappings of logical entity and physical component to + external MIB identifiers. Each physical port in the system + may be associated with a mapping to an external identifier, + which itself is associated with a particular logical + entity's naming scope. A 'wildcard' mechanism is provided to + indicate that an identifier is associated with more than one + logical entity." + ::= { entityMapping 2 } + + + +entAliasMappingEntry OBJECT-TYPE + SYNTAX EntAliasMappingEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about a particular physical equipment, logical + entity to external identifier binding. Each logical + entity/physical component pair may be associated with one + alias mapping. The logical entity index may also be used as + a 'wildcard' (refer to the entAliasLogicalIndexOrZero object + DESCRIPTION clause for details.) + + Note that only entPhysicalIndex values which represent + physical ports (i.e. associated entPhysicalClass value is + 'port(10)') are permitted to exist in this table." + INDEX { entPhysicalIndex, entAliasLogicalIndexOrZero } + ::= { entAliasMappingTable 1 } + +EntAliasMappingEntry ::= SEQUENCE { + entAliasLogicalIndexOrZero INTEGER, + entAliasMappingIdentifier RowPointer +} + +entAliasLogicalIndexOrZero OBJECT-TYPE + SYNTAX INTEGER (0..2147483647) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The value of this object uniquely identifies the logical + entity which defines the naming scope for the associated + instance of the 'entAliasMappingIdentifier' object. + + If this object has a non-zero value, then it identifies the + logical entity named by the same value of entLogicalIndex. + + If this object has a value of zero, then the mapping between + the physical component and the alias identifier for this + entAliasMapping entry is associated with all unspecified + logical entities. That is, a value of zero (the default + mapping) identifies any logical entity which does not have + an explicit entry in this table for a particular + entPhysicalIndex/entAliasMappingIdentifier pair. + + For example, to indicate that a particular interface (e.g. + physical component 33) is identified by the same value of + ifIndex for all logical entities, the following instance + might exist: + + + + entAliasMappingIdentifier.33.0 = ifIndex.5 + + In the event an entPhysicalEntry is associated differently + for some logical entities, additional entAliasMapping + entries may exist, e.g.: + + entAliasMappingIdentifier.33.0 = ifIndex.6 + entAliasMappingIdentifier.33.4 = ifIndex.1 + entAliasMappingIdentifier.33.5 = ifIndex.1 + entAliasMappingIdentifier.33.10 = ifIndex.12 + + Note that entries with non-zero entAliasLogicalIndexOrZero + index values have precedence over any zero-indexed entry. In + this example, all logical entities except 4, 5, and 10, + associate physical entity 33 with ifIndex.6." + ::= { entAliasMappingEntry 1 } + + +entAliasMappingIdentifier OBJECT-TYPE + SYNTAX RowPointer + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of this object identifies a particular conceptual + row associated with the indicated entPhysicalIndex and + entLogicalIndex pair. + + Since only physical ports are modeled in this table, only + entries which represent interfaces or ports are allowed. If + an ifEntry exists on behalf of a particular physical port, + then this object should identify the associated 'ifEntry'. + For repeater ports, the appropriate row in the + 'rptrPortGroupTable' should be identified instead. + + For example, suppose a physical port was represented by + entPhysicalEntry.3, entLogicalEntry.15 existed for a + repeater, and entLogicalEntry.22 existed for a bridge. Then + there might be two related instances of + entAliasMappingIdentifier: + entAliasMappingIdentifier.3.15 == rptrPortGroupIndex.5.2 + entAliasMappingIdentifier.3.22 == ifIndex.17 + It is possible that other mappings (besides interfaces and + repeater ports) may be defined in the future, as required. + + Bridge ports are identified by examining the Bridge MIB and + appropriate ifEntries associated with each 'dot1dBasePort', + and are thus not represented in this table." + ::= { entAliasMappingEntry 2 } + + +-- physical mapping table +entPhysicalContainsTable OBJECT-TYPE + SYNTAX SEQUENCE OF EntPhysicalContainsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table which exposes the container/containee relationships + between physical entities. This table provides equivalent + information found by constructing the virtual containment + tree for a given entPhysicalTable but in a more direct + format." + ::= { entityMapping 3 } + +entPhysicalContainsEntry OBJECT-TYPE + SYNTAX EntPhysicalContainsEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A single container/containee relationship." + INDEX { entPhysicalIndex, entPhysicalChildIndex } + ::= { entPhysicalContainsTable 1 } + +EntPhysicalContainsEntry ::= SEQUENCE { + entPhysicalChildIndex PhysicalIndex +} + +entPhysicalChildIndex OBJECT-TYPE + SYNTAX PhysicalIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of entPhysicalIndex for the contained physical + entity." + ::= { entPhysicalContainsEntry 1 } + +-- last change time stamp for the whole MIB +entLastChangeTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime at the time any of these events + occur: + * a conceptual row is created or deleted in any + of these tables: + - entPhysicalTable + - entLogicalTable + - entLPMappingTable + + + - entAliasMappingTable + - entPhysicalContainsTable + + * any instance in the following list of objects + changes value: + - entPhysicalDescr + - entPhysicalVendorType + - entPhysicalContainedIn + - entPhysicalClass + - entPhysicalParentRelPos + - entPhysicalName + - entLogicalDescr + - entLogicalType + - entLogicalCommunity + - entLogicalTAddress + - entLogicalTDomain + - entAliasMappingIdentifier " + ::= { entityGeneral 1 } + +-- Entity MIB Trap Definitions +entityMIBTraps OBJECT IDENTIFIER ::= { entityMIB 2 } +entityMIBTrapPrefix OBJECT IDENTIFIER ::= { entityMIBTraps 0 } + +entConfigChange NOTIFICATION-TYPE + STATUS current + DESCRIPTION + "An entConfigChange trap is sent when the value of + entLastChangeTime changes. It can be utilized by an NMS to + trigger logical/physical entity table maintenance polls. + + An agent must not generate more than one entConfigChange + 'trap-event' in a five second period, where a 'trap-event' + is the transmission of a single trap PDU to a list of trap + destinations. If additional configuration changes occur + within the five second 'throttling' period, then these + trap-events should be suppressed by the agent. An NMS should + periodically check the value of entLastChangeTime to detect + any missed entConfigChange trap-events, e.g. due to + throttling or transmission loss." + ::= { entityMIBTrapPrefix 1 } + +-- conformance information +entityConformance OBJECT IDENTIFIER ::= { entityMIB 3 } + +entityCompliances OBJECT IDENTIFIER ::= { entityConformance 1 } +entityGroups OBJECT IDENTIFIER ::= { entityConformance 2 } + +-- compliance statements + + +entityCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "The compliance statement for SNMP entities which implement + the Entity MIB." + MODULE -- this module + MANDATORY-GROUPS { entityPhysicalGroup, + entityLogicalGroup, + entityMappingGroup, + entityGeneralGroup, + entityNotificationsGroup } + ::= { entityCompliances 1 } + +-- MIB groupings + +entityPhysicalGroup OBJECT-GROUP + OBJECTS { + entPhysicalDescr, + entPhysicalVendorType, + entPhysicalContainedIn, + entPhysicalClass, + entPhysicalParentRelPos, + entPhysicalName + } + STATUS current + DESCRIPTION + "The collection of objects which are used to represent + physical system components, for which a single agent + provides management information." + ::= { entityGroups 1 } + +entityLogicalGroup OBJECT-GROUP + OBJECTS { + entLogicalDescr, + entLogicalType, + entLogicalCommunity, + entLogicalTAddress, + entLogicalTDomain + } + STATUS current + DESCRIPTION + "The collection of objects which are used to represent the + list of logical entities for which a single agent provides + management information." + ::= { entityGroups 2 } + +entityMappingGroup OBJECT-GROUP + OBJECTS { + + + entLPPhysicalIndex, + entAliasMappingIdentifier, + entPhysicalChildIndex + } + STATUS current + DESCRIPTION + "The collection of objects which are used to represent the + associations between multiple logical entities, physical + components, interfaces, and port identifiers for which a + single agent provides management information." + ::= { entityGroups 3 } + +entityGeneralGroup OBJECT-GROUP + OBJECTS { + entLastChangeTime + } + STATUS current + DESCRIPTION + "The collection of objects which are used to represent + general entity information for which a single agent provides + management information." + ::= { entityGroups 4 } + +entityNotificationsGroup NOTIFICATION-GROUP + NOTIFICATIONS { entConfigChange } + STATUS current + DESCRIPTION + "The collection of notifications used to indicate Entity MIB + data consistency and general status information." + ::= { entityGroups 5 } + + +END + + + -- cgit v1.2.3