Age | Commit message (Collapse) | Author |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Using the current draft:
https://tools.ietf.org/html/draft-ietf-httpbis-h2-websockets-01
|
|
Option allows to limit a frame by size before decoding its payload.
LH: I have added a test for when the limit is reached on a nofin
fragmented frame (the last commit addressed that case but it had
no test). I have fixed formatting and other, and changed the
default value to infinity since it might otherwise be incompatible
with existing code. I also added documentation and a bunch of other
minor changes.
|
|
We now flush messages that are specific to cowboy_http only.
Stream handlers should also flush their own specific messages
if necessary, although timeouts will be flushed regardless
of where they originate from.
Also renames the http_SUITE to old_http_SUITE to distinguish
new tests from old tests. Most old tests need to be removed
or converted eventually as they're legacy tests from Cowboy 1.0.
|
|
|
|
Also rename a bunch of functions to make the code easier to read.
|
|
|
|
Currently cowboy assumes that idle_timeout or request_timeout is
a number and always starts timers. Similar situation takes place
in case of preface_timeout for http2. This commit adds case for
handling infinity as a timeout, allowing to not start mentioned
timers.
|
|
|
|
|
|
|
|
|
|
|
|
The miscount occurred because of a faulty iolist split function.
The bug should now be corrected, a PropEr test has been added
and a regression test has also been added.
|
|
|
|
Allow `cowboy_router:compile` to handle colon characters within
path segments, rather than exiting with `badarg`. This is allowed
via RFC 7230 2.7 -> [RFC 3986 3.3](https://tools.ietf.org/html/rfc3986#section-3.3):
```
segment = *pchar
segment-nz = 1*pchar
segment-nz-nc = 1*( unreserved / pct-encoded / sub-delims / "@" )
; non-zero-length segment without any colon ":"
pchar = unreserved / pct-encoded / sub-delims / ":" / "@"
```
|
|
|
|
Send errors produce annoying logs and we notice the connection
is gone later on anyway.
|
|
Cases where a request body was involved could sometimes
fail depending on timing. Also fix all of the old
http_SUITE tests.
|
|
|
|
The option controls how much body we accept to skip for HTTP/1.1
connections when the user code did not consume the body fully.
It defaults to 1MB.
|
|
|
|
Also make sure the header is sent for all types of early_error
that result in the closing of the connection.
|
|
Support for these was broken during the development
of Cowboy 2.0. It is now fixed and better handled
than it ever was.
|
|
|
|
It's safer than allow it with the wrong behavior.
|
|
In some cases there could be a body sent as a response to
a HEAD request when using HTTP/2. This has been corrected.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cowboy takes a few shortcuts to avoid wasting resources when
there is a protocol error. The RFC wants us to send a different
error depending on the state of the stream at the time of the
error, and for us to maintain the connection in cases where we
would have to spend valuable resources to decode headers. In
all these cases Cowboy will simply close the connection with
an appropriate error.
|
|
Bad chunk sizes used to be accepted and could result in
a badly parsed body or a timeout. They are now properly
rejected.
Chunk extensions now have a hard limit of 129 characters.
I haven't heard of anyone using them and Cowboy does not
provide an interface for them, but we can always increase
or make configurable if it ever becomes necessary (but
I honestly doubt it).
Also a test from the old http suite could be removed. Yay!
|
|
It's worth noting that transfer-encoding now takes precedence
over content-length as recommended by the RFC, so that when
both headers are sent we only care about transfer-encoding
and explicitly remove content-length from the headers.
|
|
|
|
|
|
|