|
|
<?xml version="1.0" encoding="latin1" ?>
<!DOCTYPE erlref SYSTEM "erlref.dtd">
<erlref>
<header>
<copyright>
<year>2011</year><year>2012</year>
<holder>Ericsson AB. All Rights Reserved.</holder>
</copyright>
<legalnotice>
The contents of this file are subject to the Erlang Public License,
Version 1.1, (the "License"); you may not use this file except in
compliance with the License. You should have received a copy of the
Erlang Public License along with this software. If not, it can be
retrieved online at http://www.erlang.org/.
Software distributed under the License is distributed on an "AS IS"
basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
the License for the specific language governing rights and limitations
under the License.
</legalnotice>
<title>diameter_sctp(3)</title>
<prepared>Anders Svensson</prepared>
<responsible></responsible>
<docno></docno>
<approved></approved>
<checked></checked>
<date></date>
<rev></rev>
<file>diameter_sctp.xml</file>
</header>
<module>diameter_sctp</module>
<modulesummary>Diameter transport over SCTP.</modulesummary>
<description>
<p>
This module implements diameter transport over SCTP using <seealso
marker="kernel:gen_sctp">gen_sctp</seealso>.
It can be specified as the value of a transport_module option to
<seealso
marker="diameter#add_transport">diameter:add_transport/2</seealso>
and implements the behaviour documented in
<seealso marker="diameter_transport">diameter_transport(3)</seealso>.</p>
<marker id="start"/>
</description>
<!-- ===================================================================== -->
<funcs>
<func>
<name>start({Type, Ref}, Svc, [Opt])
-> {ok, Pid, [LAddr]} | {error, Reason}</name>
<fsummary>Start a transport process.</fsummary>
<type>
<v>Type = connect | accept</v>
<v>Ref = <seealso marker="diameter#transport_ref">diameter:transport_ref()</seealso></v>
<v>Svc = #diameter_service{}</v>
<v>Opt = {raddr, <seealso marker="kernel:inet#type-ip_address">inet:ip_address()</seealso>} | {rport, integer()} | term()</v>
<v>Pid = pid()</v>
<v>LAddr = <seealso marker="kernel:inet#type-ip_address">inet:ip_address()</seealso></v>
<v>Reason = term()</v>
</type>
<desc>
<p>
The start function required by <seealso
marker="diameter_transport#start">diameter_transport(3)</seealso>.</p>
<p>
The only diameter_sctp-specific argument is the options list.
Options <c>raddr</c> and <c>rport</c> specify the remote address
and port for a connecting transport and not valid for a listening
transport: the former is required while latter defaults to 3868 if
unspecified.
More than one <c>raddr</c> option can be specified, in which case the
connecting transport in question attempts each in sequence until
an association is established.
Remaining options are any accepted by <seealso
marker="kernel:gen_sctp#open-1">gen_sctp:open/1</seealso>, with the exception
of options <c>mode</c>, <c>binary</c>, <c>list</c>, <c>active</c>
and <c>sctp_events</c>.
Note that options <c>ip</c> and <c>port</c> specify the local address
and port respectively.</p>
<p>
Multiple <c>ip</c> options can be specified for a multihomed peer.
If none are specified then the values of <c>Host-IP-Address</c>
in the <c>#diameter_service{}</c> record are used.
(In particular, one of these must be specified.)
Option <c>port</c> defaults to 3868 for a listening transport and 0 for a
connecting transport.</p>
<warning>
<p>
An insufficiently large receive buffer may result in a peer having to
resend incoming messages: set the <seealso
marker="kernel:inet">inet(3)</seealso> option <c>recbuf</c> to increase
the buffer size.</p>
<p>
An insufficiently large send buffer may result in outgoing messages
being discarded: set the <seealso
marker="kernel:inet">inet(3)</seealso> option <c>sndbuf</c> to increase
the buffer size.</p>
</warning>
<p>
diameter_sctp uses the <c>transport_data</c> field of
the <c>#diameter_packet{}</c> record to communicate the stream on which an
inbound message has been received, or on which an outbound message
should be sent: the value will be of the form <c>{stream, Id}</c>
on an inbound message passed to a <seealso
marker="diameter_app#handle_request">handle_request</seealso> or <seealso
marker="diameter_app#handle_answer">handle_answer</seealso> callback.
For an outbound message, either <c>undefined</c> (explicitly or
by receiving the outbound message as a <c>binary()</c>) or a tuple
should be set in the return value of <seealso
marker="diameter_app#handle_request">handle_request</seealso>
(typically by retaining the value passed into this function)
or <seealso
marker="diameter_app#prepare_request">prepare_request</seealso>.
The value <c>undefined</c> uses a "next outbound stream" id and
increments this modulo the total number outbound streams.
That is, successive values of <c>undefined</c> cycle through all
outbound streams.</p>
<!-- TODO: Some way of getting at the number of available outbound -->
<!-- streams. -->
</desc>
</func>
</funcs>
<!-- ===================================================================== -->
<!-- ===================================================================== -->
<section>
<title>SEE ALSO</title>
<p>
<seealso marker="diameter_transport">diameter_transport(3)</seealso>,
<seealso marker="kernel:gen_sctp">gen_sctp(3)</seealso>,
<seealso marker="kernel:inet">inet(3)</seealso></p>
</section>
</erlref>
|
