| Age | Commit message (Collapse) | Author |
|---|
|
The order of peers presented to a diameter_app(3) pick_peer callback has
previously not been documented, but there are use cases that are
simplified by an ordering. For example, consider preferring a direct
connection to a specified Destination-Host/Realm to any host in the
realm. The implementation previously treated this as a special case by
placing matching hosts at the head of the peers list, but the
documentation made no guarantees. Now present peers in match-order, so
that the desired sorting is the result of the following filter.
{any, [{all, [host, realm]}, realm]}
The implementation is not backwards compatible in the sense that a realm
filter alone is no longer equivalent in this case. However, as stated,
the documentation never made any guarantees regarding the sorting.
|
|
In the same vein as commit 00584303, to avoid logging traffic-related
happenings.
Not that the value in diameter.hrl is just documentation: the value is
set explicitly when diameter:start_service/2 creates diameter_app
records.
|
|
* anders/diameter/doc/OTP-11583:
Correct doc on the setting of Origin-State-Id
|
|
It was incorrectly stated that the AVP would be set in an outgoing
DPR/DPA.
|
|
|
|
|
|
|
|
* anders/diameter/R16B03_release/OTP-11499:
vsn -> 1.5
Update appup for OTP-11168
Update appup for OTP-11361
Add makefile to build example dictionaries
Add recent Diameter-related RFCs
Generate diameterc.1, not diameter_compile.1
Fix documentation typos
Fix appup blunder
|
|
The former was misleading since the timer only applies to initial
connection attempts, reconnection attempts being governed by
watchdog_timer. The name is a historic remnant from a (dark, pre-OTP)
time in which RFC 3539 was followed less slavishly than it is now, and
the timer actually did apply to reconnection attempts.
Note that connect_timer corresponds to RFC 6733 Tc, while watchdog_timer
corresponds to RFC 3539 TwInit. The latter RFC makes clear that TwInit
should apply to reconnection attempts. It's less clear if only RFC 6733
is read.
Note also that reconnect_timer is still accepted for backwards
compatibility. It would be possible to add an option to make
reconnect_timer behave strictly as the name suggests (ie. ignore RFC 3539
and interpret RFC 6733 at face value; something that has some value for
testing at least) but no such option is implemented in this commit.
|
|
|
|
|
|
* anders/diameter/request_spawn/OTP-11060:
Minor doc fix
|
|
|
|
|
|
* anders/diameter/release/R16B01/OTP-11120:
vsn -> 1.4.2
Update appup for R16B01
Trailing whitespace and copyright fixes
Minor macro simplification
Move app/appsrc from src/base into src
|
|
That is, for the process that's spawned for each incoming Diameter
request message.
|
|
|
|
|
|
* anders/diameter/watchdog_leak/OTP-11019:
Minor doc fix
Add testcase to exercise reconnect behaviour
Fix watchdog table leak
|
|
|
|
Use the default address address (as selected by gen_tcp) if none is
configured, passing it in the new 'connected' message introduced by the
previous commit.
The corresponding update to diameter_sctp has to wait until problems
with inet:sockname/1 are resolved: the function currently only returns
one address, and sometimes {0,0,0,0}. See OTP-11018.
|
|
'infinity' is a valid transport_config timeout.
|
|
|
|
Allow both share_peers and use_shared_peers to be a list of nodes, or a
function that returns a list of nodes.
|
|
|
|
Make it just a number of timeouts, without a new DWR being sent.
|
|
To make the number of watchdogs sent before the transitions REOPEN ->
OKAY and OKAY -> SUSPECT configurable. Using anything other then the
default config is non-standard and should only be used for test.
|
|
RFC 3588 allowed only 3xxx result codes in an answer-message (that is,
an answer that sets the E-bit) while RFC 6733 also allows 5xxx result
codes. Setting request_errors = answer tells diameter to answer 5xxx
errors itself. Returning {answer_message, integer()} from a
handle_request callback allows both 3xxx and 5xxx result codes to be
set. {protocol_error, integer()} is retained for 3xxx result codes.
|
|
Configuring the value 'callback' all errors detected in incoming
requests to result in a handle_request callback. The default value
'answer_3xxx' is the previous behaviour in which diameter answers
protocol errors without a callback.
|
|
The value determines whether or not an unexpected message length in the
header of an incoming messages causes the peer process to exit, the
message to be discarded or handled as usual. The latter may only be
appropriate for message-oriented transport (eg. SCTP) since
stream-oriented transport (eg. TCP) may not be able to recover the
message boundary once a length error has occurred.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The former doesn't allow seealso content, which erl_docgen doesn't
enforce, resulting in mangled PDF.
|
|
* anders/diameter/CEA_timeout/OTP-10554:
Implement transport_opt() capx_timeout
Document transport_opt() capx_timeout
Minor doc fixes
|
|
* anders/diameter/transport_shutdown/OTP-10493:
Add simple DPR suite
Correct diameter:remove_transport/2 doc
Fix broken doc link
Ensure watchdog dies with transport if DPR was sent
Remove dead clause
Implement transport_opt() disconnect_cb
Document transport_opt() disconnect_cb
|
|
|
|
|
|
Presentation (order, cross-references), not content.
|
|
Error can be returned if the service process goes down while
remove_transport is ongoing.
|
|
Callback makes sending of DPR configurable.
|
|
|
|
Configuration will allow relaxation of the guard against multiple
transport connections to the same peer.
|
|
Allow 32-bit Hop-by-Hop and End-to-End identifiers to be modified by
replacing the topmost bits with a constant value. This allow services on
different nodes to generate globally unique identifiers by having each
node mask in its own constant.
|
|
|
