| Age | Commit message (Collapse) | Author |
|---|
|
|
|
* anders/diameter/R16B03_release/OTP-11499:
vsn -> 1.5
Update appup for OTP-11168
Update appup for OTP-11361
Add makefile to build example dictionaries
Add recent Diameter-related RFCs
Generate diameterc.1, not diameter_compile.1
Fix documentation typos
Fix appup blunder
|
|
* anders/diameter/timer_confusion/OTP-11168:
Rename reconnect_timer -> connect_timer
|
|
* anders/diameter/dictionary_make/OTP-11348:
Return compilable forms instead of beam
Document diameter_make:format/1 and diameter_make:flatten/1
Fix diameter_make:flatten/1
Modify type that currently causes dialyzer woe
Simplify and extend diameter_make interface
Add diameter_make:flatten/1, remove reformat/1
Adapt compiler suite to diameter_make
Remove dead code from codec suite
Extend diameter_make:codec/2
Don't pollute process dictionary in diameter_codegen:from_dict/4
Make forms a separate output from diameter_codegen
Remove last remnants of "spec"
Write as last step in code generation
Change extensions for debug output: .spec/forms -> .D/F
|
|
That is, preprocessed forms that can be passed to compile:forms/1,2.
|
|
|
|
|
|
|
|
The former was misleading since the timer only applies to initial
connection attempts, reconnection attempts being governed by
watchdog_timer. The name is a historic remnant from a (dark, pre-OTP)
time in which RFC 3539 was followed less slavishly than it is now, and
the timer actually did apply to reconnection attempts.
Note that connect_timer corresponds to RFC 6733 Tc, while watchdog_timer
corresponds to RFC 3539 TwInit. The latter RFC makes clear that TwInit
should apply to reconnection attempts. It's less clear if only RFC 6733
is read.
Note also that reconnect_timer is still accepted for backwards
compatibility. It would be possible to add an option to make
reconnect_timer behave strictly as the name suggests (ie. ignore RFC 3539
and interpret RFC 6733 at face value; something that has some value for
testing at least) but no such option is implemented in this commit.
|
|
|
|
Function can now take a literal dictionary as input, instead of a path,
and can return results instead of writing them to the filesystem.
|
|
|
|
|
|
The R16B02 release
Conflicts:
lib/sasl/vsn.mk
|
|
|
|
|
|
To accept any nested list of codepoints and binaries. A list containing
a binary was previously misinterpreted and the documentation was
incomplete.
Also, rework codec suite slightly to be able to specify values for which
decode o encode is the identity map, for which encode should succeed,
and for which encode should fail.
|
|
The R16B01 release
Conflicts:
lib/sasl/vsn.mk
|
|
|
|
|
|
* anders/diameter/request_spawn/OTP-11060:
Minor doc fix
|
|
|
|
|
|
* anders/diameter/release/R16B01/OTP-11120:
vsn -> 1.4.2
Update appup for R16B01
Trailing whitespace and copyright fixes
Minor macro simplification
Move app/appsrc from src/base into src
|
|
* anders/diameter/request_spawn/OTP-11060:
Make spawn options for request processes configurable
|
|
That is, for the process that's spawned for each incoming Diameter
request message.
|
|
Option 'accept' allows remote addresses to be configured as tuples or
regular expressions. The remote addresses for any incoming (aka
accepted) connection/association are matched against the configured
values, any non-matching address causing the connection/association to
be aborted.
|
|
|
|
|
|
* anders/diameter/5xxx_failed_avp/OTP-11092:
Fix setting of Failed-AVP on {answer_message, 5xxx} from handle_request
|
|
RFC 6733 says that certain 5xxx result codes must be accompanied by
Failed-AVP, and decode populates #diameter_packet.errors with
Result-Code/AVP pairs for errors it detects. However, Failed-AVP was not
set in the outgoing answer if the handle_request callback returned
{answer_message, 5xxx}. It is now set with the AVP from the first pair
with the specified Result-Code, if found.
Note that {answer_message, 5xxx} doesn't handle all cases in which a
5xxx answer is required, only that in which the setting above is
appropriate. If it isn't then handle_request should construct its answer
and return {reply, Ans}.
|
|
Addresses returned from a transport module were always used to populate
Host-IP-Address AVP's in an outgoing CER/CEA, which precluded the
sending of a VIP address. Transport addresses are now only used if
Host-IP-Address is unspecified.
In other words, respect any configured Host-IP-Address, regardless of
the physical addresses returned by the transport. To use the physical
addresses, don't configure Host-IP-Address.
|
|
|
|
* anders/diameter/watchdog_leak/OTP-11019:
Minor doc fix
Add testcase to exercise reconnect behaviour
Fix watchdog table leak
|
|
|
|
Use the default address address (as selected by gen_tcp) if none is
configured, passing it in the new 'connected' message introduced by the
previous commit.
The corresponding update to diameter_sctp has to wait until problems
with inet:sockname/1 are resolved: the function currently only returns
one address, and sometimes {0,0,0,0}. See OTP-11018.
|
|
A transport module can return a local address list from its start/3
function in order to specify addresses to be used as Host-IP-Address
during capabilities exchange. Now allow addresses to be communicated in
a 'connected' message in the case of a connecting transport, so that
diameter_tcp (in particular) can make local address configuration
optional, communicating the gen_tcp default after connection
establishment instead.
|
|
Diameter = the protocol
diameter = the Erlang application
|
|
* anders/diameter/app_not_configured/OTP-10972:
Fix faulty sequence validation
Add config suite
Deal with config errors detected at transport start less brutally
Move most transport_opt() validation into diameter_config
Minor doc/spec fix
Minor diameter_lib cleanup
|
|
'infinity' is a valid transport_config timeout.
|
|
Fix errors and omissions related to dictionary compilation.
|
|
|
|
|
|
Allow both share_peers and use_shared_peers to be a list of nodes, or a
function that returns a list of nodes.
|
|
|
|
Make it just a number of timeouts, without a new DWR being sent.
|
|
To make the number of watchdogs sent before the transitions REOPEN ->
OKAY and OKAY -> SUSPECT configurable. Using anything other then the
default config is non-standard and should only be used for test.
|
|
|
|
The commentary is not yet complete. It currently stops at chapter 4 of
the RFC.
|
|
|
