= ranch_tcp(3)
== Name
ranch_tcp - TCP transport
== Description
The module `ranch_tcp` implements a TCP Ranch transport.
The function `sendfile` may not work correctly when used
against files stored in a VirtualBox shared folder.
== Exports
The module `ranch_tcp` implements the interface defined
by link:man:ranch_transport(3)[ranch_transport(3)].
== Types
=== opt()
[source,erlang]
----
opt() = {backlog, non_neg_integer()}
| {buffer, non_neg_integer()}
| {delay_send, boolean()}
| {dontroute, boolean()}
| {exit_on_close, boolean()}
| {fd, non_neg_integer()}
| {high_msgq_watermark, non_neg_integer()}
| {high_watermark, non_neg_integer()}
| inet
| inet6
| {ip, inet:ip_address()}
| {ipv6_v6only, boolean()}
| {keepalive, boolean()}
| {linger, {boolean(), non_neg_integer()}}
| {low_msgq_watermark, non_neg_integer()}
| {low_watermark, non_neg_integer()}
| {nodelay, boolean()}
| {port, inet:port_number()}
| {priority, integer()}
| {raw, non_neg_integer(), non_neg_integer(), binary()}
| {recbuf, non_neg_integer()}
| {send_timeout, timeout()}
| {send_timeout_close, boolean()}
| {sndbuf, non_neg_integer()}
| {tos, integer()}
----
Listen options.
Note that additional options may be set by the protocol
module using `Transport:setopts/2`.
None of the options are required.
Please consult the `gen_tcp` and `inet` manuals for a more
thorough description of these options. This manual only aims
to provide a short description along with what the defaults
are. Defaults may be different in Ranch compared to `gen_tcp`.
Defaults are given next to the option name:
backlog (1024)::
Max length of the queue of pending connections.
buffer::
Size of the buffer used by the Erlang driver. Default
is system-dependent.
delay_send (false)::
Always queue data before sending, to send fewer, larger
packets over the network.
dontroute (false)::
Don't send via a gateway, only send to directly connected hosts.
exit_on_close (true)::
Disable to allow sending data after a close has been detected.
fd::
File descriptor of the socket, if it was opened externally.
high_msgq_watermark (8192)::
Limit in the amount of data in the socket message queue before
the queue becomes busy.
high_watermark (8192)::
Limit in the amount of data in the ERTS socket implementation's
queue before the socket becomes busy.
inet::
Set up the socket for IPv4.
inet6::
Set up the socket for IPv6.
ip::
Interface to listen on. Listen on all interfaces by default.
ipv6_v6only (false)::
Listen on IPv4 and IPv6 (false) or only on IPv6 (true).
Use with inet6.
keepalive (false)::
Enable sending of keep-alive messages.
linger ({false, 0})::
Whether to wait and how long to flush data sent before closing
the socket.
low_msgq_watermark (4096)::
Amount of data in the socket message queue before the queue
leaves busy state.
low_watermark (4096)::
Amount of data in the ERTS socket implementation's queue
before the socket leaves busy state.
nodelay (true)::
Whether to enable TCP_NODELAY.
port (0)::
TCP port number to listen on. 0 means a random port will be used.
priority (0)::
Priority value for all packets to be sent on this socket.
recbuf::
Minimum size of the socket's receive buffer.
Default is system-dependent.
send_timeout (30000)::
How long the send call may wait for confirmation before returning.
send_timeout_close (true)::
Whether to close the socket when the confirmation wasn't received.
sndbuf::
Minimum size of the socket's send buffer.
Default is system-dependent.
tos::
Value for the IP_TOS IP level option. Use with caution.
In addition, the `raw` option can be used to set system-specific
options by specifying the protocol level, the option number and
the actual option value specified as a binary. This option is not
portable. Use with caution.
=== opts()
[source,erlang]
----
opts() :: [opt()]
----
List of listen options.
== See also
link:man:ranch(7)[ranch(7)],
link:man:ranch_transport(3)[ranch_transport(3)],
link:man:ranch_ssl(3)[ranch_ssl(3)],
gen_tcp(3),
inet(3)
