|
|
<?xml version="1.0" encoding="utf-8" ?>
<!DOCTYPE chapter SYSTEM "chapter.dtd">
<chapter>
<header>
<copyright>
<year>2002</year><year>2013</year>
<holder>Ericsson AB. All Rights Reserved.</holder>
</copyright>
<legalnotice>
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
</legalnotice>
<title>Write you own test server framework</title>
<prepared>Siri Hansen</prepared>
<docno></docno>
<date></date>
<rev></rev>
<file>write_framework_chapter.xml</file>
</header>
<section>
<title>Introduction</title>
<p>The test server controller can be interfaced from the operating
system or from within Erlang. The nature of your new framework
will decide which interface to use. If you want your framework to
start a new node for each test, the operating system interface is
very convenient. If your node is already started, going from
within Erlang might be a more flexible solution.
</p>
<p>The two methods are described below.
</p>
</section>
<section>
<title>Interfacing the test server controller from Erlang</title>
<p>Using the test server from Erlang means that you have to start
the test server and then add test jobs. Use
<c>test_server_ctrl:start/0</c> to start the test server, and
<c>test_server_ctrl:stop/0</c> to stop it.
</p>
<section>
<title>Adding test jobs</title>
<p>There are many commands available for adding test cases to
the test server's job queue: <br></br>
</p>
<list type="bulleted">
<item>Single test case <br></br>
<c>test_server_ctrl:add_case/2/3</c></item>
<item>Multiple test cases from same suite <br></br>
<c>test_server_ctrl:add_cases/2/3</c></item>
<item>Test suite module or modules <br></br>
<c>test_server_ctrl:add_module/1/2</c></item>
<item>Some or all test suite modules in a directory <br></br>
<c>test_server_ctrl:add_dir/2/3</c></item>
<item>Test cases specified in a test specification file <br></br>
<c>test_server_ctrl:add_spec/1</c></item>
</list>
<p>All test suites are given a unique name, which is usually
given when the test suite is added to the job queue. In some
cases, a default name is used, as in the case when a module is
added without a specified name. The test job name is used to
store logfiles, which are stored in the `name.logs' directory
under the current directory.
</p>
<p>See the reference manual for details about the functions for
adding test jobs.
</p>
</section>
</section>
<section>
<title>Interfacing the test server controller from the operating system.</title>
<p>The function <c>run_test/1</c> is your interface in the test
server controller if you wish to use it from the operating
system. You simply start an erlang shell and invoke this function
with the <c>-s</c> option. <c>run_test/1</c> starts the test
server, runs the test specified by the command line and stops the
test server. The argument to <c>run_test/1</c> is a list of
command line flags, typically
<c>['KEY1', Value1, 'KEY2', Value2, ...]</c>.
The valid command line flags are listed in the reference manual
for <c>test_server_ctrl</c>.
</p>
<p>A typical command line may look like this <br></br>
<c>erl -noshell -s test_server_ctrl run_test KEY1 Value1 KEY2 Value2 ... -s erlang halt</c></p>
<p>Or make an alias (this is for unix/tcsh) <br></br>
<c>alias erl_test 'erl -noshell -s test_server_ctrl run_test \!* -s erlang halt'</c></p>
<p>And then use it like this <br></br>
<c>erl_test KEY1 Value1 KEY2 Value2 ...</c> <br></br>
</p>
<section>
<title>An Example</title>
<p>An example of starting a test run from the command line <br></br>
</p>
<p><c>erl -name test_srv -noshell -rsh /home/super/otp/bin/ctrsh </c> <br></br>
<c>-pa /clearcase/otp/erts/lib/kernel/test </c> <br></br>
<c>-boot start_sasl -sasl errlog_type error </c> <br></br>
<c>-s test_server_ctrl run_test SPEC kernel.spec -s erlang halt</c> <br></br>
</p>
</section>
</section>
<section>
<title>Framework callback functions</title>
<p>By defining the environment variable
<c>TEST_SERVER_FRAMEWORK</c> to a module name, the framework
callback functions can be used. The framework callback functions
are called by the test server in order let the framework interact
with the execution of the tests and to keep the framework upto
date with information about the test progress.
</p>
<p>The framework callback functions are described in the reference
manual for <c>test_server_ctrl</c>.
</p>
<p>Note that this topic is in an early stage of development, and
changes might occur.
</p>
</section>
<section>
<title>Other concerns</title>
<p>Some things to think about when writing you own test server
framework:
</p>
<list type="bulleted">
<item><c>emulator version</c> - Make sure that the intended
version of the emulator is started.
</item>
<item><c>operating system path</c> - If test cases use port
programs, make sure the paths are correct.
</item>
<item><c>recompilation</c> - Make sure all test suites are fresh
compiled.
</item>
<item><c>test_server.hrl</c> - Make sure the
<c>test_server.hrl</c> file is in the include path when
compiling test suites.
</item>
<item><c>running applications</c> - Some test suites require
some applications to be running (e.g. sasl). Make sure they are
started.
</item>
</list>
</section>
</chapter>
|
