diff options
Diffstat (limited to 'lib/ssh/doc')
| -rw-r--r-- | lib/ssh/doc/src/Makefile | 2 | ||||
| -rw-r--r-- | lib/ssh/doc/src/terminology.xml | 185 | ||||
| -rw-r--r-- | lib/ssh/doc/src/usersguide.xml | 1 |
3 files changed, 187 insertions, 1 deletions
diff --git a/lib/ssh/doc/src/Makefile b/lib/ssh/doc/src/Makefile index 77fa356092..07d4b24913 100644 --- a/lib/ssh/doc/src/Makefile +++ b/lib/ssh/doc/src/Makefile @@ -56,8 +56,8 @@ XML_CHAPTER_FILES = \ notes.xml \ introduction.xml \ using_ssh.xml \ + terminology.xml \ configure_algos.xml -# ssh_protocol.xml \ BOOK_FILES = book.xml diff --git a/lib/ssh/doc/src/terminology.xml b/lib/ssh/doc/src/terminology.xml new file mode 100644 index 0000000000..874a03b36e --- /dev/null +++ b/lib/ssh/doc/src/terminology.xml @@ -0,0 +1,185 @@ +<?xml version="1.0" encoding="utf-8" ?> +<!DOCTYPE chapter SYSTEM "chapter.dtd"> + +<chapter> + <header> + <copyright> + <year>2018</year> + <year>2018</year> + <holder>Ericsson AB. All Rights Reserved.</holder> + </copyright> + <legalnotice> + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. + + </legalnotice> + + <title>Terminology</title> + <prepared></prepared> + <docno></docno> + <approved></approved> + <date></date> + <rev></rev> + <file>terminology.xml</file> + </header> + + <section> + <title>General Information</title> + <p>In the following terms that may cause confusion are explained. + </p> + </section> + + <section> + <title>The term "user"</title> + <p>A "user" is a term that everyone understands intuitively. However, the understandings may differ which can + cause confusion. + </p> + <p>The term is used differently in <url href="http://www.openssh.com">OpenSSH</url> and SSH in Erlang/OTP. + The reason is the different environments and use cases that are not immediatly obvious. + </p> + <p>This chapter aims at explaining the differences and giving a rationale for why Erlang/OTP handles "user" as + it does. + </p> + + <section> + <title>In OpenSSH</title> + <p>Many have been in contact with the command 'ssh' on a Linux machine (or similar) to remotly log in on + another machine. One types + </p> + <code>ssh host</code> + <p>to log in on the machine named <c>host</c>. The command prompts for your password on the remote <c>host</c> and + then you can read, write and execute as your <i>user name</i> has rights on the remote <c>host</c>. There are + stronger variants with pre-distributed keys or certificates, but that are for now just details in the + authentication process. + </p> + <p>You could log in as the user <c>anotheruser</c> with + </p> + <code>ssh anotheruser@host</code> + <p>and you will then be enabled to act as <c>anotheruser</c> on the <c>host</c> if authorized correctly. + </p> + <p>So what does <i>"your user name has rights"</i> mean? In a UNIX/Linux/etc context it is exactly as that context: + The <i>user</i> could read, write and execute programs according to the OS rules. + In addition, the user has a home directory (<c>$HOME</c>) and there is a <c>$HOME/.ssh/</c> directory + with ssh-specific files. + </p> + <section> + <title>SSH password authentication</title> + <p>When SSH tries to log in to a host, the ssh protocol communicates the user name (as a string) and a password. + The remote ssh server checks that there is such a user defined and that the provided password is acceptable. + </p> + <p>If so, the user is authorized. + </p> + </section> + <section> + <title>SSH public key authentication</title> + <p>This is a stronger method where the ssh protocol brings the user name, the user's public key and some + cryptographic information which we could ignore here. + </p> + <p>The ssh server on the remote host checks: + </p> + <list> + <item>That the <i>user</i> has a home directory,</item> + <item>that home directory contains a .ssh/ directory and</item> + <item>the .ssh/ directory contains the public key just received in the <c>authorized_keys</c> file</item> + </list> + <p>if so, the user is authorized. + </p> + </section> + <section> + <title>The SSH server on UNIX/Linux/etc after a succesful authentication</title> + <p>After a succesful incoming authentication, a new process runs as the just authenticated user.</p> + <p>Next step is to start a service according to the ssh request. In case of a request of a shell, + a new one is started which handles the OS-commands that arrives from the client (that's "you"). + </p> + <p>In case of a sftp request, an sftp server is started in with the user's rights. So it could read, write or delete + files if allowed for that user. + </p> + </section> + </section> + + <section> + <title>In Erlang/OTP SSH</title> + <p>For the Erlang/OTP SSH server the situation is different. The server executes in an Erlang process + in the Erlang emulator which in turn executes in an OS process. The emulator does not try to change its + user when authenticated over the SSH protocol. + So the remote user name is only for authentication purposes in the Erlang/OTP SSH application. + </p> + <section> + <title>Password authentication in Erlang SSH</title> + <p>The Erlang/OTP SSH server checks the user name and password in the following order: + </p> + <list type="ordered"> + <item>If a + <seealso marker="ssh:ssh#option-pwdfun"><c>pwdfun</c></seealso> + is defined, that one is called and the returned boolean is the authentication result. + </item> + <item>Else, if the + <seealso marker="ssh:ssh#option-user_passwords"><c>user_passwords</c></seealso> + option is defined and the username and the password matches, the authentication is a success. + </item> + <item>Else, if the option + <seealso marker="ssh:ssh#option-password"><c>password</c></seealso> + is defined and matches the password the authentication is a success. + Note that the use of this option is not recommended in non-test code. + </item> + </list> + </section> + <section> + <title>Public key authentication in Erlang SSH</title> + <p>The user name, public key and cryptographic data (a signature) that is sent by the client, are used as follows + (some steps left out for clearity): + </p> + <list type="ordered"> + <item>A callback module is selected using the options + <seealso marker="ssh:ssh#type-key_cb_common_option"><c>key_cb</c></seealso>. + </item> + <item>The callback module is used to check that the provided public key is one of the user's pre-stored. + In case of the default callback module, the files <c>authorized_keys</c> and <c>authorized_keys2</c> + are searched in a directory found in the following order: + <list> + <item>If the option + <seealso marker="ssh:ssh_file#user_dir_fun"><c>user_dir_fun</c></seealso> + is defined, that fun is called and the returned directory is used, + </item> + <item>Else, If the option + <seealso marker="ssh:ssh#type-user_dir_common_option"><c>user_dir</c></seealso> + is defined, that directory is used, + </item> + <item>Else the subdirectory <c>.ssh</c> in the home directory of the user executing + the OS process of the Erlang emulator is used. + </item> + </list> + If the provided public key is not found, the authentication fails. + </item> + <item>Finally, if the provided public key is found, the signature provided by the client is checked with + the public key. + </item> + </list> + </section> + <section> + <title>The Erlang/OTP SSH server after a succesful authentication</title> + <p>After a successful authentication an <i>Erlang process</i> is handling the service request from the remote + ssh client. The rights of that process are those of the user of the OS process running the Erlang emulator. + </p> + <p>If a shell service request arrives to the server, an <i>Erlang shell</i> is opened in the server's emulator. + The rights in that shell is independent of the just authenticated user. + </p> + <p>In case of an sftp request, an sftp server is started with the rights of the user of the Erlang emulator's OS + process. So with sftp the authenticated user does not influence the rights. + </p> + <p>So after an authentication, the user name is not used anymore and has no influence. + </p> + </section> + </section> + </section> +</chapter> + diff --git a/lib/ssh/doc/src/usersguide.xml b/lib/ssh/doc/src/usersguide.xml index 38ffa48cde..8a4df208d8 100644 --- a/lib/ssh/doc/src/usersguide.xml +++ b/lib/ssh/doc/src/usersguide.xml @@ -36,5 +36,6 @@ </description> <xi:include href="introduction.xml"/> <xi:include href="using_ssh.xml"/> + <xi:include href="terminology.xml"/> <xi:include href="configure_algos.xml"/> </part> |